The American Architectural Manufacturers Association (AAMA) released AAMA , a voluntary specification for field testing of newly. Newly Installed Fenestration Products” and. AAMA , “Voluntary Specification for Field Testing of Newly Installed. Storefronts, Curtain Walls and Sloped. AAMA and documents, designed for field testing of newly installed fenestration products. The aforementioned. AAMA documents were often.
|Published (Last):||6 December 2013|
|PDF File Size:||6.67 Mb|
|ePub File Size:||4.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard is utilized for either field quality assurance testing or forensic testing. Read more about what our customers have to say Specifically excluded from this field check method is the testing of operable components such as operable window and doors.
AAMA Water Spray Testing
ASTM states the field test may also be made after the building is completed and in service to determine whether or not reported leakage problems are due to the failure of the installed assemblies. SITC determines what procedure to utilize based on the laboratory testing results. The specification is for quality assurance qama penetration testing only. Voluntary Specification for Field Testing of Newly Installed Storefronts, Curtain Walls and Sloped Glazing Systems This specification establishes the requirements for test specimens, apparatus, sampling, test procedures and test reports to be used in evaluating the performance of newly installed storefronts, curtain walls and sloped glazing systems.
American Architectural Manufacturers Association. There are no previous editions. This guideline is for forensic or investigative water spray testing only. Analyzing the data and establishing a cause and effect relationship between wall characteristics and the observed leakage.
This specification is for quality assurance water penetration testing only. The reviewing of project documents for the building. This differs greatly from the AAMA and AAMA field testing procedures that are intended for evaluating newly installed fenestration products or quality xama testing.
Water Penetration Field Testing
Please read our simple purchasing instructions first to ensure a smooth transaction. The diagnostic field water check is utilized for installed storefronts, curtain walls and sloped glazing systems only.
This test method exclusively aaka a uniform static air pressure difference.
See our page for further information. The AAMA was first released in and has had many changes over the years. See our AAMA page for additional information. Member discount will be reflected after successful login to the Checkout process. Read more about what our customers have to say This specification provides a guide which can be used to evaluate the installed performance of storefronts, 503-0 walls and sloped glazing systems for resistance to water penetration under controllable and reproducible wind driven rain conditions.
It can only be utilized prior to the issuance of the building occupancy permit and no later than six months after the installation of the fenestration product. The main objective of forensic water testing is to identify the leak paths through the simulation of the weather events that produced the reported leakage.
ASTM E references the following documents: Procedure B is a cyclic static air pressure difference. SITC utilizes isolation techniques to assist in identifying the source or sources of the reported water leakage.
Search by product code or category or leave the product code field blank to see a list of all AAMA publications. Begin your publication search by entering information into the fields below. Conducting the investigative testing to verify and extend hypotheses arrived at during the document review and inspection portions of the investigation using controlled and reproducible procedures.
The most current edition is the AAMA The AAMA is the proper test method for field testing of storefronts, curtain walls and sloped glazing for air leakage resistance and water penetration resistance performance. See our AAMA page for additional information if your project requires to test for the rated air leakage or rated water penetration performance.
The purpose of this voluntary guideline is to recreate leaks that are known to occur. The AAMA can be utilized if the project requires investigative testing.
The objective of forensic water spray testing is to identify and track the water migration through the simulation of wind driven rain events. The testing procedure outlined in the AAMA ASTM states that the field test may be made at the time the window, skylight, curtain wall or door assemblies are initially installed.
Procedure A is a uniform static air pressure difference.
AAMA Pubstore Product Listings –
This field check procedure is only intended to evaluate joints, gaskets and sealant details in the glazing which are designed to remain permanently closed and water amaa. The AAMA is the first edition of this voluntary guideline. These systems shall be tested per the AAMA Which would be referred to as quality assurance testing.
This specification is for quality assurance testing only. Please contact AAMA for assistance, as needed. This specification is for quality assurance testing only of storefronts, curtain walls zama sloped glazing systems and their installation.
This field water check method is not intended to test the rated or specified water performance representative of a wind driven rain event. The AAMA is the proper test method for field testing of storefronts, curtain walls and sloped glazing for air leakage and water penetration resistance performance.
This standard is utilized for laboratory or interior mock up testing only. SITC utilizes the AAMA when conducting forensic water spray testing on windows, doors, curtain walls, storefronts, slope glazing systems and exterior walls. This specification establishes the requirements for test specimens, apparatus, sampling, test procedures and test reports to be used in evaluating the performance of newly installed storefronts, curtain walls and sloped glazing systems.
This starts with a clearly defined sequence of activities that SITC follows during a investigation: There are two different procedures listed for the test method. This field check is not appropriate for testing operable components. The AAMA describes steps for calculating the approximate differential air pressures the specimens experienced during actual wind driven aamx events.